Just how to Replace a Bath Tub ( Guide).
Just how to Replace a Bath Tub ( Guide).
Blog Article
They are making several great pointers about How to Install a Bathtub Yourself as a whole in this great article directly below.
Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily accessible, the project can move rapidly; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old tub and set in the brand-new one. Ensure you have actually certified on your own for the task as well as fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This post will aid you mount a brand-new bath tub in your washroom if you have currently acquired a brand-new tub as well as do not need to alter the setup of your previous water supply pipes.
Your tools as well as product list should comprise the following:
Preparing for the Setup
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed position. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bath tub needs to wait until the tub has actually been utilized at the very least once as this will settle it right into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the faucet and the sink. Protect the faucet in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former kind must be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can break fairly very early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Write feedback down the page. We will be delighted to know your reactions about this posting. Hoping to see you back again soon. Please take the opportunity to promote this write-up if you liked it. Thanks a lot for your time. Visit us again soon.
Visit My Site Report this page